| M00 |
Program stop |
STD |
| M01 |
Optional hold |
STD |
| M02 |
End of program |
STD |
| M03 |
Spindle clockwise |
STD |
| M04 |
Spindle counterclockwise |
STD |
| M05 |
Spindle Stop |
STD |
| M06 |
Tool Chain |
OPTION |
| M07 |
NaN |
NaN |
| M08 |
Coolant 1 A |
STD |
| M09 |
Coolant 1 OFF |
STD |
| M10 |
Spindle tip operation OFF |
OPTION |
| M11 |
Spindle tip operation ON |
OPTION |
| M12 |
M-tool spindle hold |
OPTION |
| M13 |
M tool spindle clockwise |
OPTION |
| M14 |
M tool spindle counterclockwise |
OPTION |
| M15 |
C-axis positioning (positive direction) |
OPTION |
| M16 |
C-axis positioning (negative direction) |
OPTION |
| M17 |
Request for data transmission (RS232C/CEJ MATIC) |
OPTION |
| M18 |
Cancel spindle alignment |
OPTION |
| M19 |
Spindle orientation |
OPTION |
| M20 |
Tailstock Safety Zone OFF or Spindle Collision Monitoring OFF |
STD |
| M21 |
Tailstock Safety Zone ON or Spindle Collision Monitoring ON |
STD |
| M22 |
Chamfering OFF |
STD |
| M23 |
Chamfering ON |
STD |
| M24 |
Chuck Safety Zone OFF, Tool Collision Check OFF |
STD |
| M25 |
Chuck safety zone ON, tool collision test ON |
STD |
| M26 |
Thread pitch along the Z-axis |
STD |
| M27 |
Thread pitch along the X-axis |
STD |
| M28 |
Tool Collision Check OFF |
STD |
| M29 |
Tool Collision Check ON |
STD |
| M30 |
End of program |
STD |
| M31 |
NaN |
NaN |
| M32 |
Straight infeed along the thread surface (to the left end face) |
STD |
| M33 |
Zigzag infeed in threading |
STD |
| M34 |
Straight infeed along the thread surface (on the right side) |
STD |
| M35 |
Retraction of the Z-carriage for the loader grab |
OPTION |
| M36 |
Feed of the Z-carriage for the loader grab |
OPTION |
| M37 |
Retraction of the loader arm |
OPTION |
| M38 |
Loader arm feed to unloading position |
OPTION |
| M39 |
Loader arm feed to chuck position |
OPTION |
| M40 |
Neutral position in the spindle speed range |
STD |
| M41 |
Choice of spindle speed range 1 or low speed |
STD |
| M42 |
Choice of spindle speed range 2 or high speed |
STD |
| M43 |
Spindle speed range 3 |
STD |
| M44 |
Spindle speed range 4 |
STD |
| M45 |
OSL Discharge Arm Retraction |
OPTION |
| M46 |
OSL Discharge Arm Feed |
OPTION |
| M47 |
NaN |
NaN |
| M48 |
Spindle speed override |
OPTION |
| M49 |
Removing spindle speed override |
OPTION |
| M50 |
Air blower B OFF |
OPTION |
| M51 |
Air blower B A |
OPTION |
| M52 |
NaN |
NaN |
| M53 |
NaN |
NaN |
| M54 |
Automatic switching of the shift chuck |
OPTION |
| M55 |
Tailstock Retraction |
OPTION |
| M56 |
Tailstock Feed |
OPTION |
| M57 |
Lifting M63 |
OPTION |
| M58 |
Low clamping pressure |
OPTION |
| M59 |
High clamping pressure |
OPTION |
| M60 |
Removing M61 |
STD |
| M61 |
Fixed speed achieved with constant cutting speed ignore |
STD |
| M62 |
Lifting M64 |
OPTION |
| M63 |
Ignoring the response signal for M-word for spindle rotation |
OPTION |
| M64 |
Ignoring the general M-word response signal |
OPTION |
| M65 |
Ignoring the response signal for T-word |
OPTION |
| M66 |
A turret switch command was given |
OPTION |
| M67 |
Removing synchronous operation during the cam rotation cycle |
OPTION |
| M68 |
Synchronous operation A in cam rotation cycle ON |
OPTION |
| M69 |
Synchronous operation B in cam rotation cycle ON |
OPTION |
| M70 |
Manual Tool Change Command |
OPTION |
| M71 |
NaN |
NaN |
| M72 |
NaN |
NaN |
| M73 |
Tapping Pattern 1 |
OPTION |
| M74 |
Tapping Pattern 2 |
OPTION |
| M75 |
Tapping Pattern 3 |
OPTION |
| M76 |
Retraction of the parts gripper |
OPTION |
| M77 |
Feed of the parts gripper |
OPTION |
| M78 |
Relax Setting Stick 1 |
OPTION |
| M79 |
Clamping Stick 1 |
OPTION |
| M80 |
Overcut feed |
OPTION |
| M81 |
Overcut Retreat |
OPTION |
| M82 |
Chip Removal Detection ON |
OPTION |
| M83 |
Feed clamping |
STD |
| M84 |
Release turret |
STD |
| M85 |
No return to the machining starting point after the end of the roughing turning cycle |
OPTION |
| M86 |
Index determination for turret indexation in the right-hand direction |
STD |
| M87 |
Picking up M86 |
STD |
| M88 |
Air blower A OFF |
STD |
| M89 |
Pneumatic Blower A A |
STD |
| M90 |
Close cover |
OPTION |
| M91 |
Open cover |
OPTION |
| M92 |
Bar feeding device retraction |
OPTION |
| M93 |
Bar feeding device feed |
OPTION |
| M94 |
Loading the Loader |
OPTION |
| M95 |
Unloading Loader |
OPTION |
| M96 |
Parts gripper for additional spindle retraction |
OPTION |
| M97 |
Part gripper for secondary spindle feed |
OPTION |
| M98 |
Tailstock pressure low |
OPTION |
| M99 |
Tailstock pressure high |
OPTION |
| M100 |
Buffering prohibited, waiting for sync command |
OPTION |
| M101 |
External M function |
OPTION |
| M102 |
External M function |
OPTION |
| M103 |
External M function |
OPTION |
| M104 |
External M function |
OPTION |
| M105 |
External M function |
OPTION |
| M106 |
External M function |
OPTION |
| M107 |
External M function |
OPTION |
| M108 |
External M function |
OPTION |
| M109 |
Picking up M110 |
OPTION |
| M110 |
C-axis connection |
OPTION |
| M111 |
Automatic adjustment of the recording axis zero point offset |
OPTION |
| M112 |
Stop the M-tool spindle on the 3rd turret |
OPTION |
| M113 |
M-tool spindle on the 3rd turret head Forward rotation |
OPTION |
| M114 |
M-tool spindle on the 3rd turret head reverse rotation |
OPTION |
| M115 |
Open unloading grab |
OPTION |
| M116 |
Close the unloading grab |
OPTION |
| M117 |
Sensor head feed |
OPTION |
| M118 |
Sensor head retraction |
OPTION |
| M119 |
Special workpiece counter |
OPTION |
| M120 |
No workpiece confirmation |
OPTION |
| M121 |
Open/Close Bezel |
OPTION |
| M122 |
Bezel Retraction |
OPTION |
| M123 |
Bezel feed |
OPTION |
| M124 |
Check for STM Timeout ON |
OPTION |
| M125 |
STM Timeout Check OFF |
OPTION |
| M126 |
Air blower D OFF |
OPTION |
| M127 |
Air blower D A |
OPTION |
| M128 |
Tailstock swivel retraction |
OPTION |
| M129 |
Tailstock Swivel Feed |
OPTION |
| M130 |
Clamping fault detection air OFF |
OPTION |
| M131 |
Clamping fault detection air ON |
OPTION |
| M132 |
Clamping Fault Detection OFF |
OPTION |
| M133 |
Clamping Fault Detection ON |
OPTION |
| M134 |
Z-Axis Pressure Monitoring OFF |
OPTION |
| M135 |
Z-Axis Pressure Monitoring ON |
OPTION |
| M136 |
Contour Determination for Combined Fixed Cycle Optional |
OPTION |
| M137 |
Clearance for touch control lock ON |
OPTION |
| M138 |
Release for touch lock OFF |
OPTION |
| M139 |
CAM Lathe Learning Control ON |
OPTION |
| M140 |
Ignoring the response signal for constant M-tool rotation in the tapping cycle |
OPTION |
| M141 |
C-Axis Clamping Command Selection |
OPTION |
| M142 |
Coolant pressure low |
OPTION |
| M143 |
Coolant pressure high |
OPTION |
| M144 |
Additional coolant 1 OFF |
OPTION |
| M145 |
Auxiliary coolant 1 A |
OPTION |
| M146 |
C-axis release |
OPTION |
| M147 |
C-axis clamping |
OPTION |
| M148 |
NaN |
NaN |
| M149 |
NaN |
NaN |
| M150 |
Synchronized rotation OFF |
OPTION |
| M151 |
Synchronized Rotation ON |
OPTION |
| M152 |
M Tool Spindle Lock ON |
OPTION |
| M153 |
M-Tool Spindle Lock OFF |
OPTION |
| M154 |
Air blower C OFF |
OPTION |
| M155 |
Air blower C A |
OPTION |
| M156 |
tailstock lock, release lock OFF |
OPTION |
| M157 |
tailstock lock, release lock ON |
OPTION |
| M158 |
Lead Editing Function - Synchronous Operation OFF |
NaN |
| M159 |
Lead Machining Function - Synchronous Operation ON |
NaN |
| M160 |
Lifting M161 |
STD |
| M161 |
Feed rate override fixed (100%) |
STD |
| M162 |
Repealing M163 |
OPTION |
| M163 |
M tool spindle tightens speed override (100%) |
OPTION |
| M164 |
Removing M165 |
STD |
| M165 |
Ignore slide stop and single set ON |
STD |
| M166 |
Ignoring the tailstock spindle feed/retraction latch OFF |
OPTION |
| M167 |
Ignoring the tailstock spindle feed/retraction latch ON |
OPTION |
| M168 |
Transmission mode OFF (dust collector channel up) |
OPTION |
| M169 |
Transmission mode ON (dust collector channel down) |
OPTION |
| M170 |
C-Axis High Pressure Brake Release ON |
OPTION |
| M171 |
C-Axis High Pressure Brake Release OFF |
OPTION |
| M172 |
Locking release for robot inside the lathe OFF |
OPTION |
| M173 |
Interlock release on robot inside lathe ON |
OPTION |
| M174 |
Additional Coolant 2 OFF |
OPTION |
| M175 |
Auxiliary refrigerant 2 A |
OPTION |
| M176 |
Y-axis release |
OPTION |
| M177 |
Y-axis clamping |
OPTION |
| M178 |
Stopper Feed |
OPTION |
| M179 |
Stopper Retreat |
OPTION |
| M180 |
Robot/Loader Requirement 1 |
OPTION |
| M181 |
Robot/Loader Requirement 2 |
OPTION |
| M182 |
Robot/Loader Requirement 3 |
OPTION |
| M183 |
Robot/Loader Requirement 4 |
OPTION |
| M184 |
Internal locking release for chuck OFF |
OPTION |
| M185 |
Internal locking release for chuck ON |
OPTION |
| M186 |
Air blower F OFF |
OPTION |
| M187 |
Air blower F A |
OPTION |
| M188 |
Tailstock connection OFF |
OPTION |
| M189 |
Tailstock Connection ON |
OPTION |
| M190 |
Choice of G00 possible with tailstock connection |
OPTION |
| M191 |
Orientation direction of the M tool spindle specified clockwise |
OPTION |
| M192 |
Orientation direction of the M tool spindle specified counterclockwise |
OPTION |
| M193 |
Lifting M194 |
OPTION |
| M194 |
Phase Determination for Threading |
OPTION |
| M195 |
Repealing M196 |
OPTION |
| M196 |
Tapping phase travel effective |
OPTION |
| M197 |
Tapping phase travel ineffective |
OPTION |
| M198 |
STM cycle timeout ON |
OPTION |
| M199 |
STM Cycle Timeout OFF |
OPTION |
| M200 |
Unloading the Synchronized Z-Axis Feed |
OPTION |
| M201 |
Z-axis synchronized feed G13 |
OPTION |
| M202 |
Z-axis synchronized feed G14 |
OPTION |
| M203 |
Revolver approval |
OPTION |
| M204 |
Close the ATC bezel |
OPTION |
| M205 |
Open ATC bezel |
OPTION |
| M206 |
A/B slide, synchronized feed mode OFF |
OPTION |
| M207 |
A/B slide, synchronized feed mode ON |
OPTION |
| M208 |
Door Lock C, D A |
STD |
| M209 |
Door lock C, D OFF |
STD |
| M210 |
Unsync for synchronized rotation or flat rotation |
OPTION |
| M211 |
Keyway Cutting Cycle: Negative Direction |
OPTION |
| M212 |
Keyway grooving cycle: Zigzag |
OPTION |
| M213 |
Keyway Cutting Cycle: Specified Depth Infeed |
OPTION |
| M214 |
Keyway Cutting Cycle: Same Depth Infeed |
OPTION |
| M215 |
Ignoring G00 for Load Monitoring OFF |
OPTION |
| M216 |
Ignoring G00 for Load Monitoring ON |
OPTION |
| M217 |
Stop M-Tool with Alignment |
OPTION |
| M218 |
Air blower E OFF |
OPTION |
| M219 |
Air blower E A |
OPTION |
| M220 |
Flat Turning OFF |
OPTION |
| M221 |
Flat Turning OFF (1:1) |
OPTION |
| M222 |
Flat Turning OFF (1:2) |
OPTION |
| M223 |
Flat Turning OFF (1:3) |
OPTION |
| M224 |
Flat Turning OFF (1:4) |
OPTION |
| M225 |
Flat Turning OFF (1:5) |
OPTION |
| M226 |
Flat Turning OFF (1:6) |
OPTION |
| M227 |
ATC End of Operation Wait Command |
OPTION |
| M228 |
Reset next ATC tool |
OPTION |
| M229 |
AM Tool Spindle Alignment |
OPTION |
| M230 |
External M-signal |
OPTION |
| M231 |
External M-signal |
OPTION |
| M232 |
External M-signal |
OPTION |
| M233 |
External M-signal |
OPTION |
| M234 |
External M-signal |
OPTION |
| M235 |
External M-signal |
OPTION |
| M236 |
External M-signal |
OPTION |
| M237 |
External M-signal |
OPTION |
| M238 |
Flat turning for M-spindle phase change |
OPTION |
| M239 |
Face turning, spindle alignment |
OPTION |
| M240 |
Bezel 2 closed end |
OPTION |
| M241 |
Choice of M tool spindle speed range 1 or low speed |
OPTION |
| M242 |
Choice of M tool spindle speed range 2 or high speed |
OPTION |
| M243 |
Chip conveyor maintenance |
OPTION |
| M244 |
Chip conveyor start |
OPTION |
| M245 |
Changing the ACC unit of the X-axis express feed |
OPTION |
| M246 |
Face Turning, Spindle Chuck Interlock Release OFF |
OPTION |
| M247 |
Face Turning, Spindle Chuck Interlock Release ON |
OPTION |
| M248 |
Face turning, spindle chuck clamping |
OPTION |
| M249 |
Face turning, spindle chuck relax |
OPTION |
| M250 |
Retraction of the tool pusher |
OPTION |
| M251 |
Workpiece pusher feed |
OPTION |
| M252 |
Discs of Laser Interferometer Data |
OPTION |
| M253 |
Checking the Laser Interferometer Data |
OPTION |
| M254 |
Workpiece outside the ratchet feed |
OPTION |
| M255 |
Workpiece outside the ratchet retraction |
OPTION |
| M256 |
Robot/Loader Requirement 5 |
OPTION |
| M257 |
Robot/Loader Requirement 6 |
OPTION |
| M258 |
Robot/Loader Requirement 7 |
OPTION |
| M259 |
Robot/Loader Requirement 8 |
OPTION |
| M260 |
Step-by-step feed mode OFF |
OPTION |
| M261 |
Step-by-step feed mode ON |
OPTION |
| M262 |
Auxiliary coolant 3 OFF / tool V way, coolant OFF |
OPTION |
| M263 |
Auxiliary Coolant 3 ON/Tool V Way, Coolant ON |
OPTION |
| M264 |
Overlay Mode Restriction, Rapid Traverse Release OFF |
OPTION |
| M265 |
Restriction of overlay mode, rapid traverse release ON |
OPTION |
| M266 |
R-spindle collet test close |
OPTION |
| M267 |
R-Spindle Collet Test Open |
OPTION |
| M268 |
Tailstock Feed Mode Not Possible |
OPTION |
| M269 |
Switch the optical sensor to OFF |
OPTION |
| M270 |
Optical sensor start/stop, switch on optical sensor |
OPTION |
| M271 |
Spindle ON Extreme Creep Mode |
OPTION |
| M272 |
Extreme creep mode of the spindle OFF |
OPTION |
| M273 |
2. Software Limit Enabled |
OPTION |
| M274 |
2. Software limit disabled |
OPTION |
| M275 |
Special ATC sequence |
OPTION |
| M276 |
ATC, 1st aperture close |
OPTION |
| M277 |
ATC, 1st aperture open |
OPTION |
| M278 |
Relax Setting Stick 2 |
OPTION |
| M279 |
Clamping Stick 2 |
OPTION |
| M280 |
Cancel M280 |
OPTION |
| M281 |
Laser sensor effective |
OPTION |
| M282 |
Sled, gradual retreat |
OPTION |
| M283 |
Slide, step-by-step feed |
OPTION |
| M284 |
Air blower in the chuck |
OPTION |
| M285 |
Workpiece counting |
OPTION |
| M286 |
Follower arm feed (close chuck) |
OPTION |
| M287 |
Follower retraction (open chuck) |
OPTION |
| M288 |
Secondary spindle air blower OFF |
OPTION |
| M289 |
Secondary Spindle Air Blower ON |
OPTION |
| M290 |
Close ceiling door |
OPTION |
| M291 |
Open the ceiling door |
OPTION |
| M292 |
Unloader Retreat |
OPTION |
| M293 |
Unloader Feed |
OPTION |
| M294 |
No thermal deviation, data transfer |
OPTION |
| M295 |
No thermal deviation, cancel data transfer |
OPTION |
| M296 |
Change the time constant (for fewer crop marks) |
OPTION |
| M297 |
Changing the time constant (for efficient shaping) |
OPTION |
| M298 |
Picking up M299 |
OPTION |
| M299 |
Cancel repeat mode |
OPTION |
| M300 |
Close gripper A |
NaN |
| M301 |
Open Gripper A |
OPTION |
| M302 |
Switching Gripper, Position A |
OPTION |
| M303 |
Switch Gripper, Position B |
OPTION |
| M304 |
NaN |
NaN |
| M305 |
NaN |
NaN |
| M306 |
Feed Workpiece Pusher A |
OPTION |
| M307 |
Workpiece Pusher A Retraction |
OPTION |
| M308 |
Swivel Gripper A |
OPTION |
| M309 |
Swivel Gripper B |
OPTION |
| M310 |
Close gripper B |
OPTION |
| M311 |
Open Gripper B |
OPTION |
| M312 |
Turn tandem loader |
OPTION |
| M313 |
Gripper clamping, error checking activated |
OPTION |
| M314 |
Gripper clamping, error checking deactivated |
OPTION |
| M315 |
Joint rotation angle 90° |
OPTION |
| M316 |
Feed Workpiece Pusher B |
OPTION |
| M317 |
Retraction Workpiece Pusher B |
OPTION |
| M318 |
Robot/Loader Air Blower ON |
OPTION |
| M319 |
Robot/Loader Air Blower OFF |
OPTION |
| M320 |
Robot/Loader, General M-Code 1 |
OPTION |
| M321 |
Robot/Loader, General M-Code 2 |
OPTION |
| M322 |
Robot/Loader, General M-Code 3 |
OPTION |
| M323 |
Robot/Loader, General M-Code 4 |
OPTION |
| M324 |
Robot/Loader, General M-Code 5 |
OPTION |
| M325 |
Robot/Loader, General M-Code 6 |
OPTION |
| M326 |
Robot/Loader, General M-Code 7 |
OPTION |
| M327 |
Robot/Loader, General M-Code 8 |
OPTION |
| M328 |
Exit Position Requirement Valid |
OPTION |
| M329 |
Initial Position Request Invalid |
OPTION |
| M330 |
NC Start |
OPTION |
| M331 |
Buffering prohibited |
OPTION |
| M332 |
Chip Check Enabled |
OPTION |
| M333 |
Chip inspection disabled |
OPTION |
| M334 |
Collision with NC lathe OFF |
OPTION |
| M335 |
Collision with NC lathe ON |
OPTION |
| M336 |
External start |
OPTION |
| M337 |
Workpiece counting |
OPTION |
| M338 |
Determination of the A-workpiece |
OPTION |
| M339 |
Determination of the B workpiece |
OPTION |
| M340 |
Robot/Loader, General M-Code 9 |
OPTION |
| M341 |
Robot/Loader, General M-Code 10 |
OPTION |
| M342 |
Robot/Loader, General M-Code 11 |
OPTION |
| M343 |
Robot/loader, general M-code 12 |
OPTION |
| M344 |
Robot/Loader, General M-Code 13 |
OPTION |
| M345 |
Robot/Loader, General M-Code 14 |
OPTION |
| M346 |
Robot/Loader, General M-Code 15 |
OPTION |
| M347 |
Robot/Loader, General M-Code 16 |
OPTION |
| M348 |
External Program Selection (BCD) |
OPTION |
| M349 |
Termination of the Lot |
OPTION |
| M350 |
NC Lathe, Option 1 |
OPTION |
| M351 |
NC Lathe, Option 2 |
OPTION |
| M352 |
NC Lathe, Option 3 |
OPTION |
| M353 |
Retraction of the tool pusher |
OPTION |
| M354 |
Workpiece pusher feed |
OPTION |
| M355 |
Tailstock Retreat 2 |
OPTION |
| M356 |
Tailstock Feed 2 |
OPTION |
| M357 |
Change vehicle type info |
OPTION |
| M358 |
NG ratchet full, workpiece |
OPTION |
| M359 |
Spindle Alignment, 2nd Position |
OPTION |
| M360 |
2. Face Turning Spindle, Clamping Fault Detection Air OFF |
OPTION |
| M361 |
2. Face Turning Spindle, Clamping Fault Detection Air ON |
OPTION |
| M362 |
R-turning device, close gripper |
OPTION |
| M363 |
R-turning device, open gripper |
OPTION |
| M364 |
R-Turning Device, Retraction |
OPTION |
| M365 |
R-Turning Device, Feed |
OPTION |
| M366 |
NC lathe output position, travel command 1 |
OPTION |
| M367 |
NC lathe output position, travel command 2 |
OPTION |
| M368 |
NC lathe output position, travel command 3 |
OPTION |
| M369 |
NC lathe starting position, travel command 4 |
OPTION |
| M370 |
Robot/Loader, General M-Code 17 |
OPTION |
| M371 |
Robot/Loader, General M-Code 18 |
OPTION |
| M372 |
Robot/Loader, General M-Code 19 |
OPTION |
| M373 |
Robot/Loader, General M-Code 20 |
OPTION |
| M374 |
Robot/Loader, General M-Code 21 |
OPTION |
| M375 |
Robot/Loader, General M-Code 22 |
OPTION |
| M376 |
Robot/Loader, General M-Code 23 |
OPTION |
| M377 |
Robot/Loader, General M-Code 24 |
OPTION |
| M378 |
Swivel V-Gripper A |
OPTION |
| M379 |
Swivel V-Gripper B |
OPTION |
| M380 |
NC lathe, power saving mode OFF |
OPTION |
| M381 |
NC Lathe, Power Saving Mode ON |
OPTION |
| M382 |
NC Lathe Home Position, Traverse Command 5 |
OPTION |
| M383 |
NC lathe output position, travel command 6 |
OPTION |
| M384 |
NC lathe starting position, travel command 7 |
OPTION |
| M385 |
NC lathe starting position, travel command 8 |
OPTION |
| M386 |
Workpiece Turner, Retraction |
OPTION |
| M387 |
Workpiece, turn |
OPTION |
| M388 |
2. Air blower A OFF |
OPTION |
| M389 |
2. Air blower A A A |
OPTION |
| M390 |
2. Close the door |
OPTION |
| M391 |
2. Open the door |
OPTION |
| M392 |
Spindle pendulum movement |
OPTION |
| M393 |
2. Spindle head downwards |
OPTION |
| M394 |
2. Spindle head upward |
OPTION |
| M395 |
Feed lock release when 2nd spindle is not on top or bottom position OFF |
OPTION |
| M396 |
Feed lock release when 2nd spindle is not on top or bottom position ON |
OPTION |
| M397 |
Position Index for Turret Determination |
OPTION |
| M398 |
Measuring unit at the start of machine measurement |
OPTION |
| M399 |
2. NC lathe output position, travel command 4 |
OPTION |
| M400 |
Stopper Lock OFF |
OPTION |
| M401 |
Stopper Lock ON |
OPTION |
| M402 |
End of Program Message |
OPTION |
| M403 |
Unclamping the B-axis |
OPTION |
| M404 |
B-axis tensioning |
OPTION |
| M405 |
Ignoring the Loader Feed Stop |
OPTION |
| M406 |
Setting stick connection OFF (clamping) |
OPTION |
| M407 |
Setting stick connection ON (relax) |
OPTION |
| M408 |
Robot/loader interface interlock release OFF |
OPTION |
| M409 |
Robot/Loader Interface Interlock Release ON |
OPTION |
| M410 |
Tailstock Quill Axle Thrust Force, Selection 1 |
OPTION |
| M411 |
Tailstock Quill Axle Thrust Force, Selection 2 |
OPTION |
| M412 |
Robot/Loader Requirement 9 |
OPTION |
| M413 |
Robot/Loader Requirement 10 |
OPTION |
| M414 |
Robot/Loader Requirement 11 |
OPTION |
| M415 |
Robot/Loader Requirement 12 |
OPTION |
| M416 |
Robot/Loader Requirement 13 |
OPTION |
| M417 |
Robot/Loader Requirement 14 |
OPTION |
| M418 |
Robot/Loader Requirement 15 |
OPTION |
| M419 |
2. Spindle alignment |
OPTION |
| M420 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M421 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M422 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M423 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M424 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M425 |
M-word for macro function CALL (fixed subprogram name) |
OPTION |
| M426 |
Ring probe, Clear selection |
OPTION |
| M427 |
Ring Sensor, Pick ON |
OPTION |
| M428 |
Tailstock Position, Data Request |
OPTION |
| M429 |
Select Chuck Clamping Pressure |
OPTION |
| M430 |
2. Spindle clamping error air OFF |
OPTION |
| M431 |
2. Spindle Clamping Error Air ON |
OPTION |
| M432 |
Tailstock Air Fault Detection OFF |
OPTION |
| M433 |
Tailstock Air Fault Detection ON |
OPTION |
| M434 |
Engine Fault Conditions OFF |
OPTION |
| M435 |
Machine Fault Conditions ON |
OPTION |
| M436 |
Rod Feeder Help, Command 1 |
OPTION |
| M437 |
Ring probe, low sensitivity |
OPTION |
| M438 |
Ring probe, high sensitivity |
OPTION |
| M439 |
Coolant 4 OFF |
OPTION |
| M440 |
Refrigerant 4 A |
OPTION |
| M441 |
M-word for macro function CALL |
OPTION |
| M442 |
M-word for macro function CALL |
OPTION |
| M443 |
M-word for macro function CALL |
OPTION |
| M444 |
M-word for macro function CALL |
OPTION |
| M445 |
M-word for macro function CALL |
OPTION |
| M446 |
M-word for macro function CALL |
OPTION |
| M447 |
M-word for macro function CALL |
OPTION |
| M448 |
M-word for macro function CALL |
OPTION |
| M449 |
M-word for macro function CALL |
OPTION |
| M450 |
M-word for macro function CALL |
OPTION |
| M451 |
M-word for macro function CALL |
OPTION |
| M452 |
M-word for macro function CALL |
OPTION |
| M453 |
M-word for macro function CALL |
OPTION |
| M454 |
M-word for macro function CALL |
OPTION |
| M455 |
M-word for macro function CALL |
OPTION |
| M456 |
M-word for macro function CALL |
OPTION |
| M457 |
M-word for macro function CALL |
OPTION |
| M458 |
M-word for macro function CALL |
OPTION |
| M459 |
M-word for macro function CALL |
OPTION |
| M460 |
M-word for macro function CALL |
OPTION |
| M461 |
Workpiece stopper, retraction |
OPTION |
| M462 |
Workpiece stopper, feed |
OPTION |
| M463 |
Relax the turning device |
OPTION |
| M464 |
Clamping the turning device |
OPTION |
| M465 |
Turning device, reverse gear back |
OPTION |
| M466 |
Turning device, reverse gear |
OPTION |
| M467 |
Determination of the high/low mode of coolants |
OPTION |
| M468 |
Notification of the cutting process completed |
OPTION |
| M469 |
Spindle in the middle, SOL 1 A |
OPTION |
| M470 |
Workpiece ejector unit downward, spindle in the middle, SOL 2 OFF |
OPTION |
| M471 |
Workpiece ejector unit upward, spindle in the middle, SOL 2 A |
OPTION |
| M472 |
Release of bezel lock OFF |
OPTION |
| M473 |
Release of bezel lock ON |
OPTION |
| M474 |
Coolant 5 OFF, spindle in the middle, SOL 4 OFF |
OPTION |
| M475 |
Coolant 5 A, Spindle in Center, SOL 4 ON |
OPTION |
| M476 |
Discharge Panel, Interlock Release OFF |
OPTION |
| M477 |
Discharge Panel, Interlock Release ON |
OPTION |
| M478 |
Unloader call possible, confirmation |
OPTION |
| M479 |
ZB axis, variable minus limit change |
OPTION |
| M480 |
Turning device, receiving side |
OPTION |
| M481 |
Turning device, loading side |
OPTION |
| M482 |
Tailstock feed to workpiece support position (tailstock ABSOCODER) |
OPTION |
| M483 |
Clamp chuck 2 (clamping lever/collet) |
OPTION |
| M484 |
Clamp chuck 2 (clamping lever/collet) |
OPTION |
| M485 |
Natural chuck: clamping |
OPTION |
| M486 |
Natural chuck: unclamp |
OPTION |
| M487 |
Compe chuck: clamping |
OPTION |
| M488 |
Compe chuck: unclamp |
OPTION |
| M489 |
X-axes, close lubricating oil discharge circuit |
OPTION |
| M490 |
X-axes, open lubricating oil drainage circuit |
OPTION |
| M491 |
Open the unloader closer |
OPTION |
| M492 |
Close the discharger closer |
OPTION |
| M493 |
Unloading device conveyor left |
OPTION |
| M494 |
Unloading device conveyor right |
OPTION |
| M495 |
Open unloading gripper, relax workpiece unloading device gripper |
OPTION |
| M496 |
Close the unloading gripper, clamp the workpiece unloading device gripper |
OPTION |
| M497 |
Unloading arm, swivel feed |
OPTION |
| M498 |
Unloading arm, swivel retraction |
OPTION |
| M499 |
Switching chuck, locking release |
OPTION |
| M500 |
Unloading, fixed cycle |
OPTION |
| M501 |
Tool Counting 1 |
OPTION |
| M502 |
Tool Count 2 |
OPTION |
| M503 |
Tool Counting 3 |
OPTION |
| M504 |
Tool Counting 4 |
OPTION |
| M505 |
Tool Counting 5 |
OPTION |
| M506 |
Tool Counting 6 |
OPTION |
| M507 |
Tool Counting 7 |
OPTION |
| M508 |
Tool Counting 8 |
OPTION |
| M509 |
Tugboat, lock release OFF |
OPTION |
| M510 |
Tugboat, interlock release ON |
OPTION |
| M511 |
Rear Air Chuck Clamping |
OPTION |
| M512 |
Relax Front Air Chuck |
OPTION |
| M513 |
X-axis, variable plus limit testing ON |
OPTION |
| M514 |
X-axis, variable plus limit test OFF |
OPTION |
| M515 |
Start initial measurement data output |
OPTION |
| M516 |
Start workpiece measurement data output |
OPTION |
| M517 |
Start cleaning of the centrifugal separator (spindle index position free) |
OPTION |
| M518 |
Measurement finished |
OPTION |
| M519 |
M spindle ON extreme creep rotation mode |
OPTION |
| M520 |
Extreme creep speed rotation mode of the M-spindle OFF |
OPTION |
| M521 |
Status light, green flashing ON |
OPTION |
| M522 |
Status light, green flashing OFF |
OPTION |
| M523 |
Status light, yellow flashing ON |
OPTION |
| M524 |
Status light, yellow flashing OFF |
OPTION |
| M525 |
Status light, red flashing ON |
OPTION |
| M526 |
Status light, flashing red OFF |
OPTION |
| M527 |
Oil mist OFF |
OPTION |
| M528 |
Oil mist ON |
OPTION |
| M529 |
Tailstock Feed Output OFF |
OPTION |
| M530 |
Oil supply OFF |
OPTION |
| M531 |
Oil level max. |
OPTION |
| M532 |
Oil level STD. |
OPTION |
| M533 |
Oil level min. |
OPTION |
| M534 |
Support roller retraction |
OPTION |
| M535 |
Support roller feed |
OPTION |
| M536 |
Loader Request Signal |
OPTION |
| M537 |
Workpiece Pusher, Cancel Locking Release |
OPTION |
| M538 |
Workpiece pusher, locking release |
OPTION |
| M539 |
Workpiece Puller, Retraction |
OPTION |
| M540 |
Workpiece Puller, Feed |
OPTION |
| M541 |
NaN |
OPTION |
| M542 |
NaN |
OPTION |
| M543 |
Workpiece stator movement, upward to center |
OPTION |
| M544 |
Workpiece stator movement, from center upwards |
OPTION |
| M545 |
Workpiece stand movement, down to center |
OPTION |
| M546 |
Workpiece stator movement, from center down |
OPTION |
| M547 |
Workpiece support, pulling position (right slide) |
OPTION |
| M548 |
Workpiece support, insertion position (left slide) |
OPTION |
| M549 |
Longitudinal positioning device, retraction |
OPTION |
| M550 |
Longitudinal Positioning Device, Feed |
OPTION |
| M551 |
Loader Carriage Stop |
OPTION |
| M552 |
Middle door opening position |
OPTION |
| M553 |
NaN |
OPTION |
| M554 |
NaN |
OPTION |
| M555 |
Hobbing, synchronized rotation mode OFF |
OPTION |
| M556 |
Hobbing, synchronized rotation mode ON |
OPTION |
| M557 |
During hobbing, move in the Z-axis direction when the carriage is held |
OPTION |
| M558 |
During hobbing, move in the X-axis direction when the carriage is held |
OPTION |
| M559 |
Synchronized Axis Motion Zero Offset (CAM Lathe) |
OPTION |
| M560 |
C. Scratches and Grippers closed , Reitst. Lateral deburring and reburring , device Rückz. |
OPTION |
| M561 |
C.Scratches and grippers open. , Reitst. lateral deburring and pre-grinding, back-to-back device |
OPTION |
| M562 |
Close nip probe / retraction of the chuck side deburring device |
OPTION |
| M563 |
Open nip probe / feed of chuck side deburring device |
OPTION |
| M564 |
C-axis positioning, pin removed |
OPTION |
| M565 |
C-axis positioning, pin inserted |
OPTION |
| M566 |
Vibration Cutter Start |
OPTION |
| M567 |
Vibration Cutting Device Stop |
OPTION |
| M568 |
Turret B, special release of optional index control OFF |
OPTION |
| M569 |
Turret B, special release of optional index control ON |
OPTION |
| M570 |
Universal M-Function 9 |
OPTION |
| M571 |
Universal M-Function 9 |
OPTION |
| M572 |
Universal M-Function 10 |
OPTION |
| M573 |
Universal M-Function 10 |
OPTION |
| M574 |
Universal M-Function 11 |
OPTION |
| M575 |
Universal M-Function 11 |
OPTION |
| M576 |
Universal M-Function 12 |
OPTION |
| M577 |
Universal M-Function 12 |
OPTION |
| M578 |
Spindle brake OFF |
OPTION |
| M579 |
Spindle brake ON |
OPTION |
| M580 |
X/Z ascending/descending time constant (default) |
OPTION |
| M581 |
X/Z ascending/descending time constant (pattern 1) |
OPTION |
| M582 |
X/Z ascending/descending time constant (Pattern 2) |
OPTION |
| M583 |
X/Z ascending/descending time constant (pattern 3) |
OPTION |
| M584 |
Start trade fairs |
OPTION |
| M585 |
No workpiece, cutting mode ON |
OPTION |
| M586 |
No workpiece, cutting mode ON |
OPTION |
| M587 |
2. Spindle head law brake |
OPTION |
| M588 |
2. Clamping the spindle head |
OPTION |
| M589 |
Workpiece Unloading |
OPTION |
| M590 |
Cycle Time Measurement: Stop Measurement |
OPTION |
| M591 |
Cycle Time Measurement: Start Measurement |
OPTION |
| M592 |
Universal M-Function 13 |
OPTION |
| M593 |
Universal M-Function 13 |
OPTION |
| M594 |
Universal M-Function 14 |
OPTION |
| M595 |
Universal M-Function 14 |
OPTION |
| M596 |
Universal M-Function 15 |
OPTION |
| M597 |
Universal M-Function 15 |
OPTION |
| M598 |
Universal M-Function 16 |
OPTION |
| M599 |
Universal M-Function 16 |
OPTION |
| M600 |
M-tool spindle, clamping angle 90° |
OPTION |
| M601 |
M-tool spindle, clamping angle 270° |
OPTION |
| M602 |
M-tool spindle, clamping angle 0 |
OPTION |
| M603 |
M-tool spindle, clamping angle 180 |
OPTION |
| M604 |
B-axis, single-sided positioning mode OFF |
OPTION |
| M605 |
B-axis, single-sided positioning mode ON |
OPTION |
| M606 |
Y-axis barrier function OFF |
OPTION |
| M607 |
Y-axis barrier function ON |
OPTION |
| M608 |
2. Refrigerant 1 A |
OPTION |
| M609 |
2. Coolant 1 OFF |
OPTION |
| M610 |
2. Spindle tap operation OFF |
OPTION |
| M611 |
2. Spindle tap operation ON |
OPTION |
| M612 |
During hobbing, move in the Y-axis direction when the carriage is held |
OPTION |
| M613 |
Workpiece Pusher Confirmation, Air OFF |
OPTION |
| M614 |
Confirmation of workpiece pusher, air ON |
OPTION |
| M615 |
Start Monitoring Part Readout |
OPTION |
| M616 |
Close aperture |
OPTION |
| M617 |
Open aperture |
OPTION |
| M618 |
2. Unalign the spindle |
OPTION |
| M619 |
2. Spindle Alignment 1 |
OPTION |
| M620 |
2. Spindle Alignment 2 |
OPTION |
| M621 |
1. Spindle alignment position (electric chuck position) |
OPTION |
| M622 |
Hobbing, retraction direction Y-axis minus value |
OPTION |
| M623 |
Hobbing, retraction direction Y-axis plus value |
OPTION |
| M624 |
Confirmation light for walking speed ON |
OPTION |
| M625 |
B-axis, contour milling ON |
OPTION |
| M626 |
2. Air blower D OFF |
OPTION |
| M627 |
2. Air blower D A |
OPTION |
| M628 |
2. Air blower E OFF |
OPTION |
| M629 |
2. Air blower E A |
OPTION |
| M630 |
2. Spindle, clamping fault detection air OFF |
OPTION |
| M631 |
2. Spindle, clamping fault detection air ON |
OPTION |
| M632 |
Receiver OFF |
OPTION |
| M633 |
Receiver ON |
OPTION |
| M634 |
Interference with NC lathe OFF (2nd spindle/R-spindle) |
OPTION |
| M635 |
Interference with NC lathe ON (2nd spindle/R spindle) |
OPTION |
| M636 |
Index feed: Index command 0 |
OPTION |
| M637 |
Index Feed: Index Command 45 |
OPTION |
| M638 |
Index Feed: Index Command 90 |
OPTION |
| M639 |
Index Feed: Index Command 135 |
OPTION |
| M640 |
Index Feed: Index Command 180 |
OPTION |
| M641 |
Index Feed: Index Command 225 |
OPTION |
| M642 |
Index Feed: Index Command 270 |
OPTION |
| M643 |
Index Feed: Index Command 315 |
OPTION |
| M644 |
2. Coolant 2 OFF |
OPTION |
| M645 |
2. Coolant 2 A |
OPTION |
| M646 |
Magnet Level 1 |
OPTION |
| M647 |
Magnet Level 2 |
OPTION |
| M648 |
Magnet Level 3 |
OPTION |
| M649 |
Spindle Head Index |
OPTION |
| M650 |
2. Air blower B OFF |
OPTION |
| M651 |
2. Air blower B A |
OPTION |
| M652 |
Main Magazine, Cancel Tool Identification |
OPTION |
| M653 |
1. Spindle AAC Position Index |
OPTION |
| M654 |
2. Air blower C OFF |
OPTION |
| M655 |
2. Air blower C ON |
OPTION |
| M656 |
Low load detection OFF |
OPTION |
| M657 |
Low Load Sensing ON |
OPTION |
| M658 |
Chuck pressure low |
OPTION |
| M659 |
Chuck pressure high |
OPTION |
| M660 |
ACC Blower |
OPTION |
| M661 |
A-Chuck Index (Machining Station) |
OPTION |
| M662 |
B-Chuck Index (Processing Station) |
OPTION |
| M663 |
AAC chuck, locking release OFF |
OPTION |
| M664 |
AAC chuck, lock release ON |
OPTION |
| M665 |
Loader, Clamping Fault Detection Air OFF |
OPTION |
| M666 |
Loader, Clamping Fault Detection Air ON |
OPTION |
| M667 |
Main drive, clamping device unit retraction |
OPTION |
| M668 |
Main drive, clamping device unit feed |
OPTION |
| M669 |
Main drive, clamping device unit pendulum movement |
OPTION |
| M670 |
Auxiliary Drive, Clamping Device Unit Pendulum Movement |
OPTION |
| M671 |
Spindle, low acceleration mode ON |
OPTION |
| M672 |
Spindle, low acceleration mode OFF |
OPTION |
| M673 |
Quality Inspection Mode OFF |
OPTION |
| M674 |
2. Coolant 3 OFF |
OPTION |
| M675 |
2. Coolant 3 A |
OPTION |
| M676 |
Loader Request, Response |
OPTION |
| M677 |
Timeout Check ON |
OPTION |
| M678 |
Timeout Check OFF |
OPTION |
| M679 |
Workpiece cover downwards |
OPTION |
| M680 |
Workpiece cover upwards |
OPTION |
| M681 |
Close the threaded rolling head |
OPTION |
| M682 |
Open thread rolling head |
OPTION |
| M683 |
2. Clamp the spindle chuck |
OPTION |
| M684 |
2. Relax spindle chuck |
OPTION |
| M685 |
Stop Hiring |
OPTION |
| M686 |
Status indicator light OFF |
OPTION |
| M687 |
Status indicator light ON |
OPTION |
| M688 |
2. Air blower A OFF |
OPTION |
| M689 |
2. Air blower A A A |
OPTION |
| M690 |
2. Close the door |
OPTION |
| M691 |
2. Open the door |
OPTION |
| M692 |
Tool breakage detection, interlock release ON |
OPTION |
| M693 |
Tool breakage detection, interlock release OFF |
OPTION |
| M694 |
Spindle speed deviation control OFF |
OPTION |
| M695 |
Control of spindle speed deviation ON |
OPTION |
| M696 |
Spindle phase synchronization mode OFF |
OPTION |
| M697 |
Spindle phase synchronization mode ON |
OPTION |
| M698 |
Tool breakage detection, sensor feed |
OPTION |
| M699 |
Tool breakage detection, sensor retraction |
OPTION |
| M700 |
Fog Collector OFF |
OPTION |
| M701 |
Mist Collector ON |
OPTION |
| M702 |
Mist Collector Retreat |
OPTION |
| M703 |
Fog Collector Feed |
OPTION |
| M704 |
Workpiece stand retraction / rattle control retraction |
OPTION |
| M705 |
Workpiece stand retraction / rattle control feed |
OPTION |
| M706 |
Medium centering unit, feed |
OPTION |
| M707 |
Centering unit, feed |
OPTION |
| M708 |
Medium centering unit, retraction |
OPTION |
| M709 |
Centering unit, retraction |
OPTION |
| M710 |
Relax centering unit |
OPTION |
| M711 |
Clamping the centering unit |
OPTION |
| M712 |
Tool Breakage Detection ON |
OPTION |
| M713 |
Tool breakage detection OFF |
OPTION |
| M714 |
Workpiece Change Request |
OPTION |
| M715 |
Workpiece Off Requisition |
OPTION |
| M716 |
Tool Loading Request |
OPTION |
| M717 |
Tool Unloading Requirement |
OPTION |
| M718 |
Loader, cycle start |
OPTION |
| M719 |
Loader, cycle stop |
OPTION |
| M720 |
Specified Alarm C Effective |
OPTION |
| M721 |
Specified Alarm C Ineffective |
OPTION |
| M722 |
Tool Life Confirmation |
OPTION |
| M723 |
Tailstock, feed level switch active |
OPTION |
| M724 |
tailstock, feed level switch deactivated |
OPTION |
| M725 |
Loader timeout, test start |
OPTION |
| M726 |
Loader timeout, test stop |
OPTION |
| M727 |
Loader motor lock ON |
OPTION |
| M728 |
Loader motor lock OFF |
OPTION |
| M729 |
Workpiece stand downwards |
OPTION |
| M730 |
Workpiece stand upwards |
OPTION |
| M731 |
Workpiece counter A |
OPTION |
| M732 |
Workpiece counter B |
OPTION |
| M733 |
Workpiece counter C |
OPTION |
| M734 |
Workpiece counter D |
OPTION |
| M735 |
Workpiece counter E |
OPTION |
| M736 |
Workpiece counter F |
OPTION |
| M737 |
Workpiece counter G |
OPTION |
| M738 |
M739 Cancel |
OPTION |
| M739 |
Remove the workpiece stand mounting pin |
OPTION |
| M740 |
Workpiece stator movement, interlock ON |
OPTION |
| M741 |
Workpiece stand movement, locking OFF |
OPTION |
| M742 |
Bezel XB axis, locking release OFF |
OPTION |
| M743 |
Bezel XB axis, locking release ON |
OPTION |
| M744 |
Spindle alignment, speed override effective |
OPTION |
| M745 |
Spindle alignment, speed overdrive ineffective |
OPTION |
| M746 |
Open Ball Valve |
OPTION |
| M747 |
Close Ball Valve |
OPTION |
| M748 |
Tailstock brake OFF |
OPTION |
| M749 |
Tailstock Brake ON |
OPTION |
| M750 |
Centering unit, machining cycle |
OPTION |
| M751 |
Workpiece conveyor, feed |
OPTION |
| M752 |
Workpiece conveyor, retraction |
OPTION |
| M753 |
Workpiece conveyor, clockwise |
OPTION |
| M754 |
Workpiece conveyor, counterclockwise |
OPTION |
| M755 |
Workpiece Conveyor, Stop |
OPTION |
| M756 |
Slow down turret speed, control OFF |
OPTION |
| M757 |
Slow down turret speed, control ON |
OPTION |
| M758 |
Unclamping the chuck |
OPTION |
| M759 |
Clamping the pick-up chuck |
OPTION |
| M760 |
Choose a water coolant |
OPTION |
| M761 |
Choose oil coolant |
OPTION |
| M762 |
Coolant Return Pump OFF |
OPTION |
| M763 |
Coolant Return Pump ON |
OPTION |
| M764 |
Chuck (transducer/collet), locking release OFF |
OPTION |
| M765 |
Chuck (transducer/collet), locking release ON |
OPTION |
| M766 |
Workpiece conveyor, interlock release OFF |
OPTION |
| M767 |
Workpiece conveyor, interlock release ON |
OPTION |
| M768 |
Tailstock chuck, locking release OFF |
OPTION |
| M769 |
Tailstock chuck, locking release ON |
OPTION |
| M770 |
Pick-up chuck, blower OFF |
OPTION |
| M771 |
Pick-up chuck, blower ON |
OPTION |
| M772 |
Bezel 2, Retraction |
OPTION |
| M773 |
Bezel 2, Feed |
OPTION |
| M774 |
Bezel 3 open |
OPTION |
| M775 |
Close bezel 3 |
OPTION |
| M776 |
Bezel 3, Retraction |
OPTION |
| M777 |
Bezel 3, Feed |
OPTION |
| M778 |
Setting stick pressure low |
OPTION |
| M779 |
Setting Stick Pressure High |
OPTION |
| M780 |
Open rod feeder bezel |
OPTION |
| M781 |
Close bar feeder steady rest |
OPTION |
| M782 |
Settings program button OFF |
OPTION |
| M783 |
Tailstock chuck clamping |
OPTION |
| M784 |
Tailstock chuck relax |
OPTION |
| M785 |
Center position of unloader, standby ON |
OPTION |
| M786 |
Center position of unloader, standby OFF |
OPTION |
| M787 |
Air Drill OFF |
OPTION |
| M788 |
Air Drill ON |
OPTION |
| M789 |
Spindle Alignment 3 |
OPTION |
| M790 |
NaN |
NaN |
| M791 |
NaN |
NaN |
| M792 |
Cross Cutting, Confirmation Unit Retraction |
OPTION |
| M793 |
Cross-cutting, confirmation unit feed |
OPTION |
| M794 |
Parts Conveyor ON |
OPTION |
| M795 |
Parts Conveyor OFF |
OPTION |
| M796 |
Traverse, execute |
OPTION |
| M797 |
NaN |
NaN |
| M798 |
NaN |
NaN |
| M799 |
NaN |
NaN |
| M800 |
Air blower H OFF |
OPTION |
| M801 |
Air blower H A |
OPTION |
| M802 |
Cycle Air Blast: ON |
OPTION |
| M803 |
High pressure, coolant level A |
OPTION |
| M804 |
High pressure, coolant level B |
OPTION |
| M805 |
High pressure, coolant level C |
OPTION |
| M806 |
High pressure, coolant level D |
OPTION |
| M807 |
Cutting feed, interlock release OFF |
OPTION |
| M808 |
Cutting feed, interlock release ON |
OPTION |
| M809 |
W-axis movement, lock release OFF |
OPTION |
| M810 |
W-axis movement, interlock release ON |
OPTION |
| M811 |
Clamping the tool |
OPTION |
| M812 |
Clamping the tool |
OPTION |
| M813 |
ATC Aperture, Interlock Release OFF |
OPTION |
| M814 |
ATC Aperture, Interlock Release ON |
OPTION |
| M815 |
Clamping the headstock |
OPTION |
| M816 |
Spindle override active in threading |
OPTION |
| M817 |
Spindle override deactive during threading |
OPTION |
| M818 |
Unloader Carrier 2, Feed |
OPTION |
| M819 |
Unloader carrier 2, retraction |
OPTION |
| M820 |
Tool Preparation Cycle, Macro Command |
OPTION |
| M821 |
Thermal Deviation Compensation Function OFF |
OPTION |
| M822 |
Thermal Deviation Compensation Function ON |
OPTION |
| M823 |
2. Spindle clockwise (W-axis overlap mode) |
OPTION |
| M824 |
2. Spindle counterclockwise (W-axis overlap mode) |
OPTION |
| M825 |
2. Stop spindle (W-axis overlap mode) |
OPTION |
| M826 |
Loader axle movement, locking OFF |
OPTION |
| M827 |
Loader axle movement, locking ON |
OPTION |
| M828 |
Roll Lowering OFF |
OPTION |
| M829 |
Roller Lowering ON |
OPTION |
| M830 |
XB-W Axis Interference Test OFF |
OPTION |
| M831 |
XB-W Axis Interference Test ON |
OPTION |
| M832 |
M-TOOL Index, Interlock Release OFF |
OPTION |
| M833 |
M-TOOL Index, Lock Release ON |
OPTION |
| M834 |
Lubricating oil engine, fixed output OFF |
OPTION |
| M835 |
Lubricating Oil Engine, Fixed Output ON |
OPTION |
| M836 |
Air blower F OFF |
OPTION |
| M837 |
Air blower F A |
OPTION |
| M838 |
Loader Gripper A, Workpiece Pusher Confirmation |
OPTION |
| M839 |
Loader Gripper B, Workpiece Pusher Confirmation |
OPTION |
| M840 |
ATC shutter, simultaneous opening/closing |
OPTION |
| M841 |
2. Spindle, creep speed winding option (W-axis override mode) |
OPTION |
| M842 |
2. Spindle, rapid traverse winding option (W-axis override mode) |
OPTION |
| M843 |
ATC Tool, Blower OFF |
OPTION |
| M844 |
ATC Tool, Blower ON |
OPTION |
| M845 |
Oil mist mode OFF |
OPTION |
| M846 |
Oil mist mode ON |
OPTION |
| M847 |
Tailstock Retraction on End Position Command |
OPTION |
| M848 |
Tailstock, Measurement |
OPTION |
| M849 |
Secondary spindle 2, chuck locking release OFF |
OPTION |
| M850 |
Secondary spindle 2, Chuck interlock release ON |
OPTION |
| M851 |
Clamping the chuck of the secondary spindle 2 |
OPTION |
| M852 |
Clamping the chuck of the secondary spindle 2 |
OPTION |
| M853 |
Air blower G OFF |
OPTION |
| M854 |
Air blower G ON |
OPTION |
| M855 |
Coolant 7 OFF |
OPTION |
| M856 |
Refrigerant 7 A |
OPTION |
| M857 |
Coolant 8 OFF |
OPTION |
| M858 |
Refrigerant 8 A |
OPTION |
| M859 |
Emergency withdrawal completed |
OPTION |
| M860 |
Tailstock side, bar removal device A roller |
OPTION |
| M861 |
tailstock side, bar removal device OFF roller |
OPTION |
| M862 |
Chuck side, bar removal device ON roller |
OPTION |
| M863 |
Chuck Side, Bar Removal Device Roller OFF |
OPTION |
| M864 |
Grinding Whetstone Spindle Unit, Retraction |
OPTION |
| M865 |
Grinding Whetstone Spindle Unit, Feed |
OPTION |
| M866 |
Collision Avoidance System, Unblock Collision Search OFF |
OPTION |
| M867 |
Collision Avoidance System, Reverse Collision Search ON |
OPTION |
| M868 |
Pneumatic blower OFF |
OPTION |
| M869 |
Chip Air Blower ON |
OPTION |
| M870 |
Air blower I OFF |
OPTION |
| M871 |
Air blower I A |
OPTION |
| M872 |
Touch Adjuster, Open Aperture |
OPTION |
| M873 |
Touch Adjuster, Close Aperture |
OPTION |
| M874 |
Tool Retraction OFF |
OPTION |
| M875 |
Tool Retraction ON |
OPTION |
| M876 |
Release for touch lock OFF |
OPTION |
| M877 |
Clearance for touch control lock ON |
OPTION |
| M878 |
Hold data |
OPTION |
| M879 |
Hold Data Pick Up |
OPTION |
| M880 |
2. Air blower H OFF |
OPTION |
| M881 |
2. Air blower H A |
OPTION |
| M882 |
Clamping Fault Detection Zero Point Displacement |
OPTION |
| M883 |
Synchronous spindle rotation, clamp both chucks, release the lock |
OPTION |
| M884 |
Delete data |
OPTION |
| M885 |
Clear Data 2 |
OPTION |
| M886 |
2. Air blower F OFF |
OPTION |
| M887 |
2. Air blower F A |
OPTION |
| M888 |
Synchronous C-axis mode OFF |
OPTION |
| M889 |
Synchronous C-axis mode ON (turret A) |
OPTION |
| M890 |
Synchronous C-Axis Mode ON (Turret B) |
OPTION |
| M891 |
Secondary spindle, C-axis connection OFF |
OPTION |
| M892 |
Secondary Spindle, C-Axis Connection ON |
OPTION |
| M893 |
M-tool spindle clockwise typing operation ON |
NaN |
| M894 |
M-Tool Spindle Tipping Counterclockwise ON |
NaN |
| M895 |
M-tool spindle tipping operation OFF |
NaN |
| M896 |
NaN |
NaN |
| M897 |
NaN |
NaN |
| M898 |
Parts Turner Gripper, Air Blower OFF |
OPTION |
| M899 |
Parts Turner Gripper, Air Blower ON |
OPTION |
| M900 |
Secondary spindle pendulum movement |
OPTION |
| M901 |
Workpiece washing, close the panel |
OPTION |
| M902 |
Workpiece washing, open aperture |
OPTION |
| M903 |
Workpiece washing, solid cycle |
OPTION |
| M904 |
Edit mode, interlock release |
OPTION |
| M905 |
NaN |
NaN |
| M906 |
NaN |
NaN |
| M907 |
NaN |
NaN |
| M908 |
ATC Air Blower OFF |
OPTION |
| M909 |
AATC Air Blower ON |
OPTION |
| M910 |
Relax M-axis |
OPTION |
| M911 |
Chuck diameter 1 |
OPTION |
| M912 |
Chuck diameter 2 |
OPTION |
| M913 |
Chuck diameter 3 |
OPTION |
| M914 |
Chuck diameter 4 |
OPTION |
| M915 |
Chuck diameter 5 |
OPTION |
| M916 |
No tool, lock release OFF |
OPTION |
| M917 |
No tool, interlock release ON |
OPTION |
| M918 |
Chuck center, low pressure |
OPTION |
| M919 |
Chuck center, high pressure |
OPTION |
| M920 |
Light OFF Command |
OPTION |
| M921 |
Spindle Tipping Counterclockwise ON |
OPTION |
| M922 |
System Link Output OFF |
OPTION |
| M923 |
System Link Output ON |
OPTION |
| M924 |
Slider retraction |
OPTION |
| M925 |
Slide feed |
OPTION |
| M926 |
TOOL 1, Close the gripper |
OPTION |
| M927 |
TOOL 1, Open Gripper |
OPTION |
| M928 |
TOOL 2, Close gripper |
OPTION |
| M929 |
TOOL 2, Open Gripper |
OPTION |
| M930 |
Relax M-axis |
OPTION |
| M931 |
Clamping M-spindle |
OPTION |
| M932 |
Long tool, lock release OFF |
OPTION |
| M933 |
Long tool, interlock release ON |
OPTION |
| M934 |
Pallet change |
OPTION |
| M935 |
Workpiece adjustment completed |
OPTION |
| M936 |
tailstock, approach position |
OPTION |
| M937 |
2. Close gripper A (close Y-gripper) |
OPTION |
| M938 |
2. Open Gripper A (Open Y-Gripper) |
OPTION |
| M939 |
2. Optional stop |
OPTION |
| M940 |
Disable Interruption Program |
OPTION |
| M941 |
Activate Interruption Program (O941) |
OPTION |
| M942 |
Activate Interrupt Program (O942) |
OPTION |
| M943 |
Activate Interrupt Program (O943) |
OPTION |
| M944 |
Activate Interrupt Program (O944) |
OPTION |
| M945 |
Activate Interrupt Program (O945) |
OPTION |
| M946 |
2. Close gripper B (close V-gripper) |
OPTION |
| M947 |
2. Open gripper B (open V-gripper) |
OPTION |
| M948 |
Bezel 3 closed end |
OPTION |
| M949 |
Workpiece Assessment, Air OFF |
OPTION |
| M950 |
Workpiece Assessment, Air ON |
OPTION |
| M951 |
Chuck position of the left front door |
OPTION |
| M952 |
Free position of the left front door |
OPTION |
| M953 |
-- |
NaN |
| M954 |
APC Tension Clamp, Locking Release OFF |
OPTION |
| M955 |
APC Tension Clamp, Interlock Release ON |
OPTION |
| M956 |
APC interference, interlock release OFF |
OPTION |
| M957 |
APC interference, interlock release ON |
OPTION |
| M958 |
Tool Washer, Coolant OFF |
OPTION |
| M959 |
Tool Washer, Coolant ON |
OPTION |
| M960 |
C-axis positioning (near direction) |
OPTION |
| M961 |
Clamping chuck, error checking activated |
OPTION |
| M962 |
Clamp finger chuck, error check deactivated |
OPTION |
| M963 |
Clamp collet chuck, error check deactivated |
OPTION |
| M964 |
Retraction level in multiple processing cycle, fixed level |
OPTION |
| M965 |
Retraction level in multiple processing cycle, standard level |
OPTION |
| M966 |
Swivel gripper, upright position |
OPTION |
| M967 |
Chuck, eccentric motion OFF |
OPTION |
| M968 |
Chuck, eccentric movement ON |
OPTION |
| M969 |
Time constant for better cutting appearance OFF |
OPTION |
| M970 |
Time Constant for Better Cut Appearance ON |
OPTION |
| M971 |
Manual break switch not possible OFF |
OPTION |
| M972 |
Manual break switch not possible ON |
OPTION |
| M973 |
Loader gripper outside the gripper diameter |
OPTION |
| M974 |
Loader gripper inside the gripper diameter |
OPTION |
| M975 |
W-Axis Turret Interference, Interlock Release OFF |
OPTION |
| M976 |
W-Axis Turret Interference, Interlock Release ON |
OPTION |
| M977 |
M-axis, synchronized thread torque monitoring OFF |
OPTION |
| M978 |
M-Axis, Synchronized Thread Torque Monitoring ON |
OPTION |
| M979 |
Vibration Cutting Tool B ON |
OPTION |
| M980 |
Vibration cutting tool B OFF |
OPTION |
| M981 |
Vibration Cutting Tool C ON |
OPTION |
| M982 |
Vibration cutting tool C OFF |
OPTION |
| M983 |
Thermal Deformation Compensation Adjusted for X-C Axis Displacement |
OPTION |
| M984 |
Thermal Deformation Compensation of the X-C Axis OFF |
OPTION |
| M985 |
Thermal Deformation Compensation of the X-C Axis A |
OPTION |
| M986 |
Automatic evaluation |
OPTION |
| M987 |
Edit |
OPTION |
| M988 |
Measurement Mode |
OPTION |
| M989 |
Thermal Deformation Compensation OFF |
OPTION |
| M990 |
Thermal Deformation Compensation ON |
OPTION |
| M991 |
LBB clamping fault detection, air OFF |
OPTION |
| M992 |
LBB Clamping Fault Detection Air ON |
OPTION |
| M993 |
Close LBB stick closure |
OPTION |
| M994 |
Open LBB stick closure |
OPTION |
| M995 |
NaN |
NaN |
| M996 |
NaN |
NaN |
| M997 |
NaN |
NaN |
| M998 |
NaN |
NaN |
| M999 |
NaN |
NaN |
| M1000 |
NaN |
NaN |
| M1001 |
NaN |
NaN |
| M1002 |
NaN |
NaN |
| M1003 |
Close APC door |
OPTION |
| M1004 |
Open APC door |
OPTION |
| M1005 |
Loading long tool 1 |
OPTION |
| M1006 |
Load long tool 2 |
OPTION |
| M1007 |
Load long tool 3 |
OPTION |
| M1008 |
Load long tool 4 |
OPTION |
| M1009 |
Unloading long tool |
OPTION |
| M1010 |
Tool Offset, Cancel Zero Point Detection OFF |
OPTION |
| M1011 |
Tool Offset, Cancel Zero Point Detection ON |
OPTION |
| M1012 |
NaN |
NaN |
| M1013 |
NaN |
NaN |
| M1014 |
NaN |
NaN |
| M1015 |
NaN |
NaN |
| M1016 |
NaN |
NaN |
| M1017 |
Release of bezel lock, ZB axis |
OPTION |
| M1018 |
1. Unclamp the NC bezel nut |
OPTION |
| M1019 |
1. Clamp the NC bezel nut |
OPTION |
| M1020 |
2. Unclamp the NC bezel nut |
OPTION |
| M1021 |
2. Clamp the NC bezel saddle |
OPTION |
| M1022 |
3. Unclamp the NC bezel nut |
OPTION |
| M1023 |
3. Clamp the NC bezel nut |
OPTION |
| M1024 |
NaN |
NaN |
| M1025 |
NaN |
NaN |
| M1026 |
Multi-bezel lock OFF |
OPTION |
| M1027 |
Multi-bezel locking ON |
OPTION |
| M1028 |
NaN |
NaN |
| M1029 |
NaN |
NaN |
| M1030 |
Automatic matrix switcher positioning 1 |
OPTION |
| M1031 |
Automatic matrix switcher positioning 2 |
OPTION |
| M1032 |
Automatic matrix switcher positioning 3 |
OPTION |
| M1033 |
Automatic matrix switcher positioning 4 |
OPTION |
| M1034 |
Automatic matrix switcher positioning 5 |
OPTION |
| M1035 |
Automatic matrix switcher positioning 6 |
OPTION |
| M1036 |
Automatic matrix switcher positioning 7 |
OPTION |
| M1037 |
Automatic matrix switcher positioning 8 |
OPTION |
| M1038 |
Automatic matrix switcher positioning 9 |
OPTION |
| M1039 |
Automatic matrix switcher positioning 10 |
OPTION |
| M1040 |
Clamping the matrix switcher |
OPTION |
| M1041 |
Unclamping the matrix switcher |
OPTION |
| M1042 |
Attachment Index Command, Front |
OPTION |
| M1043 |
Attachment Index Command, Left |
OPTION |
| M1044 |
Attachment Index Command, Rear |
OPTION |
| M1045 |
Attachment Index Command, Right |
OPTION |
| M1046 |
Attachment index counterclockwise |
OPTION |
| M1047 |
Attachment Indexing (Clockwise) with RH Command |
OPTION |
| M1048 |
Attachment Indexing (Counterclockwise) with RH Command |
OPTION |
| M1049 |
Ignore attachment indexing at NC in position |
OPTION |
| M1050 |
AT clamp |
OPTION |
| M1051 |
AT relax |
OPTION |
| M1052 |
Hang AT |
OPTION |
| M1053 |
Unhook AT |
OPTION |
| M1054 |
AT Preparation for relaxation |
OPTION |
| M1055 |
Attachment carrier OFF |
OPTION |
| M1056 |
Attachment Carrier ON |
OPTION |
| M1057 |
Tool change command (horizontal) |
OPTION |
| M1058 |
Tool change command (vertical) |
OPTION |
| M1059 |
No next tool |
OPTION |
| M1060 |
Manual tool change |
OPTION |
| M1061 |
Change attachment |
OPTION |
| M1062 |
ATC cover, attach tool |
OPTION |
| M1063 |
ATC cover, remove tool |
OPTION |
| M1064 |
Additional Axle: Clamp A-Axis |
OPTION |
| M1065 |
Additional axis: Unclamp A-axis |
OPTION |
| M1066 |
Additional axis: B-axis tensioning |
OPTION |
| M1067 |
Additional axle: Clamp out the B-axis |
OPTION |
| M1068 |
Additional axis: C-axis clamping |
OPTION |
| M1069 |
Additional Axis: C-Axis Release |
OPTION |
| M1070 |
Opposite spindle, cancel alignment |
OPTION |
| M1071 |
Coolant supply through the tool, high pressure OFF |
OPTION |
| M1072 |
Coolant supply through the tool, high pressure ON |
OPTION |
| M1073 |
Preparation for tool change for vertical spindle |
OPTION |
| M1074 |
Continuous tool change between vertical and horizontal spindles |
OPTION |
| M1075 |
Continuous different tool changes between vertical and horizontal spindles |
OPTION |
| M1076 |
Clamping the horizontal spindle tool |
OPTION |
| M1077 |
Clamping the horizontal spindle tool |
OPTION |
| M1078 |
Changing the Horizontal Spindle Tool |
OPTION |
| M1079 |
Oil mist injection |
OPTION |
| M1080 |
Oil mist cycle mode ON for vertical spindle |
OPTION |
| M1081 |
Preparation for tool change for horizontal spindle |
OPTION |
| M1082 |
Coolant supply through the spindle, medium pressure |
OPTION |
| M1083 |
M-Spindle Alignment when Rotating Counterclockwise |
OPTION |
| M1084 |
M-Spindle Alignment in Clockwise/Counterclockwise Rotation |
OPTION |
| M1085 |
Ejector bore, high pressure coolant ON |
OPTION |
| M1086 |
Attachment, blower ON |
OPTION |
| M1087 |
Touch Probe Flush ON |
OPTION |
| M1088 |
Clamping the C-axis of the opposite spindle |
OPTION |
| M1089 |
Clamp the C-axis of the opposite spindle |
OPTION |
| M1090 |
Overload detection invalid for M-spindle |
OPTION |
| M1091 |
Overload detection valid for M-spindle |
OPTION |
| M1092 |
Workpiece clamping device, air blower OFF |
OPTION |
| M1093 |
Workpiece Clamping Device, Air Blower ON |
OPTION |
| M1094 |
Clamping the workpiece |
OPTION |
| M1095 |
Unclamping the workpiece |
OPTION |
| M1096 |
Select cooling system for vertical spindle |
OPTION |
| M1097 |
Select Cooling System for Horizontal Spindle |
OPTION |
| M1098 |
Sensor Air Blower OFF |
OPTION |
| M1099 |
Sensor Air Blower ON |
OPTION |
| M1100 |
Retraction cycle command for active ATC tool |
OPTION |
| M1101 |
ATC Ready (Write No. of Active Tool) |
OPTION |
| M1102 |
ATC Air Blower OFF |
OPTION |
| M1103 |
ATC Air Blower ON |
OPTION |
| M1104 |
M-Spindle Rotation Reversal OFF |
OPTION |
| M1105 |
M-Spindle Rotation Reversal ON |
OPTION |
| M1106 |
Count up cycle counter |
OPTION |
| M1107 |
Clamp the holding device or chuck 2 |
OPTION |
| M1108 |
Clamp out the holding device or chuck 2 |
OPTION |
| M1109 |
Semi-dry, MIN flow |
OPTION |
| M1110 |
Semi-dry, MIN nozzle |
OPTION |
| M1111 |
Semi-dry, MAX flow |
OPTION |
| M1112 |
Semi-dry, MAX nozzle |
OPTION |
| M1113 |
Clamping Bracket 3 |
OPTION |
| M1114 |
Clamp out holding device 3 |
OPTION |
| M1115 |
Assess pallet status |
OPTION |
| M1116 |
Indexing the B-Axis Attachment |
OPTION |
| M1117 |
2. Automatic door close |
OPTION |
| M1118 |
2. Automatic door opening |
OPTION |
| M1119 |
NaN |
NaN |
| M1120 |
Set workpiece, monitoring ON |
OPTION |
| M1121 |
Set workpiece, monitor OFF |
OPTION |
| M1122 |
Workpiece Fit Condition Test, Air ON |
OPTION |
| M1123 |
Workpiece Fit Condition Test, Air OFF |
OPTION |
| M1124 |
Activate Chuck PB During NC Movement |
OPTION |
| M1125 |
Retract attachment above the magazine |
OPTION |
| M1126 |
Pull back the adapter connector over the magazine |
OPTION |
| M1127 |
M06 Answer [Close ATC Shutter] ineffective |
OPTION |
| M1128 |
Canceling M1127 |
OPTION |
| M1129 |
Swivel the magazine pot to the tool change position |
OPTION |
| M1130 |
Pallet-off request from the stacking crane is not allowed |
OPTION |
| M1131 |
Pallet-off request from the stacking crane is permissible |
OPTION |
| M1132 |
Contactless sensor; Laser OFF |
OPTION |
| M1133 |
Contactless sensor; Laser ON |
OPTION |
| M1134 |
Hybrid coolant: choose oil |
OPTION |
| M1135 |
Hybrid coolant: choose water |
OPTION |
| M1136 |
Holding device 1, low pressure clamping |
OPTION |
| M1137 |
Cancel disabling the lifting limit |
OPTION |
| M1138 |
Deactivate lifting limit |
OPTION |
| M1139 |
Selection of 1st gear for M-spindle in synchronized tapping mode |
OPTION |
| M1140 |
Selection of 2nd gear for M-spindle with synchronized tapping mode |
OPTION |
| M1141 |
Selection of 3rd gear for M-spindle with synchronized tapping mode |
OPTION |
| M1142 |
Semi-dry, MID flow |
OPTION |
| M1143 |
Semi-dry, MID nozzle |
OPTION |
| M1144 |
Washing the clamping device OFF |
OPTION |
| M1145 |
Washing the clamping device ON |
OPTION |
| M1146 |
L-Tool Clamping Locking Piston |
OPTION |
| M1147 |
L-Tool Clamping Locking Piston |
OPTION |
| M1148 |
L-tool unhooking position (M-spindle 0 degrees) |
OPTION |
| M1149 |
L-tool hook position (M-spindle 15 degrees) |
OPTION |
| M1150 |
L-Tool 180-degree unhooking position (M-spindle 180 degrees) |
OPTION |
| M1151 |
L-Tool 180 Degree Hook Position (M-Spindle 195 Degree) |
OPTION |
| M1152 |
Control mode of the 2nd spindle |
OPTION |
| M1153 |
Tailstock Control Mode |
OPTION |
| M1154 |
Sensor Air Blower (Inner Diameter) OFF |
OPTION |
| M1155 |
Sensor Air Blower (Inner Diameter) ON |
OPTION |
| M1156 |
Touch Adjuster (Inner Diameter) Feed |
OPTION |
| M1157 |
Touch setter (inner diameter) retraction |
OPTION |
| M1158 |
Magazine indexing of the current tool |
OPTION |
| M1159 |
W-axis cutting mode |
OPTION |
| M1160 |
Coolant for 2nd bezel OFF |
OPTION |
| M1161 |
Coolant for 2nd bezel ON |
OPTION |
| M1162 |
Coolant for 3rd bezel OFF |
OPTION |
| M1163 |
Coolant for 3rd bezel ON |
OPTION |
| M1164 |
2nd bezel blower OFF |
OPTION |
| M1165 |
2nd bezel blower ON |
OPTION |
| M1166 |
3rd Bezel Blower OFF |
OPTION |
| M1167 |
3rd Bezel Blower ON |
OPTION |
| M1168 |
Round Spindle Conveyor STOP |
OPTION |
| M1169 |
Round Spindle Conveyor ON Clockwise |
OPTION |
| M1170 |
Round Spindle Conveyor ON Counterclockwise |
OPTION |
| M1171 |
Tailstock adjustment 2nd spindle |
OPTION |
| M1172 |
Tailstock adjustment 1st spindle |
OPTION |
| M1173 |
Angle Head, Coolant OFF |
OPTION |
| M1174 |
Angle head, coolant ON |
OPTION |
| M1175 |
Angle head, blower OFF |
OPTION |
| M1176 |
Angle head, blower ON |
OPTION |
| M1177 |
Unloader carriage positioning (L-spindle INSIDE) |
OPTION |
| M1178 |
Unloader carriage positioning (L-spindle to the OUTSIDE) |
OPTION |
| M1179 |
Unloader carriage positioning (R-spindle INSIDE) |
OPTION |
| M1180 |
Unloader carriage positioning (R-spindle to the OUTSIDE) |
OPTION |
| M1181 |
Unloader Carriage Positioning (Retraction Point) |
OPTION |
| M1182 |
Unloading grab up |
OPTION |
| M1183 |
Discharge grab downwards |
OPTION |
| M1184 |
Unloading grab center |
OPTION |
| M1185 |
Enable Unloader Call, Acknowledgment 2 |
OPTION |
| M1186 |
NaN |
NaN |
| M1187 |
NaN |
NaN |
| M1188 |
AJC Coolant OFF |
OPTION |
| M1189 |
AJC Refrigerant ON |
OPTION |
| M1190 |
Tailstock, Tool Clamping Fault Detection Air OFF |
OPTION |
| M1191 |
Tailstock, Tool Clamping Fault Detection Air ON |
OPTION |
| M1192 |
Wait exclusively ON |
OPTION |
| M1193 |
Cancel Wait Exclusively |
OPTION |
| M1194 |
Check tailstock mode, lock release |
OPTION |
| M1195 |
Measuring Sensor Unit Feed |
OPTION |
| M1196 |
Measurement Sensor Unit Retraction |
OPTION |
| M1197 |
Select Coolant Pressure |
OPTION |
| M1198 |
Air Drill 2 A |
OPTION |
| M1199 |
Air Drill 2 OFF |
OPTION |
| M1200 |
Control of M-spindle speed deviation OFF |
OPTION |
| M1201 |
Control of M-spindle speed deviation ON |
OPTION |
| M1202 |
Stretching the APC pallet |
OPTION |
| M1203 |
APC pallet tensioning |
OPTION |
| M1204 |
APC pallet, unclamp cone cone |
OPTION |
| M1205 |
APC pallet, clamping cone cone |
OPTION |
| M1206 |
APC Pallet Table Down |
OPTION |
| M1207 |
APC pallet table up |
OPTION |
| M1208 |
3. Coolant 1 A |
OPTION |
| M1209 |
3. Coolant 1 OFF |
OPTION |
| M1210 |
Change of spindle rotation speed in thread mode OFF |
OPTION |
| M1211 |
Change of Spindle Rotation Speed in Thread Mode ON |
OPTION |
| M1212 |
NaN |
NaN |
| M1213 |
NaN |
NaN |
| M1214 |
Close telescopic ceiling cover |
OPTION |
| M1215 |
Open Telescopic Ceiling Cover |
OPTION |
| M1216 |
NaN |
NaN |
| M1217 |
NaN |
NaN |
| M1218 |
NaN |
NaN |
| M1219 |
NaN |
NaN |
| M1220 |
NaN |
NaN |
| M1221 |
NaN |
NaN |
| M1222 |
NaN |
NaN |
| M1223 |
NaN |
NaN |
| M1224 |
NaN |
NaN |
| M1225 |
NaN |
NaN |
| M1226 |
NaN |
NaN |
| M1227 |
NaN |
NaN |
| M1228 |
3. Air blower E OFF |
OPTION |
| M1229 |
3. Air blower E A |
OPTION |
| M1230 |
NaN |
NaN |
| M1231 |
NaN |
NaN |
| M1232 |
NaN |
NaN |
| M1233 |
NaN |
NaN |
| M1234 |
NaN |
NaN |
| M1235 |
NaN |
NaN |
| M1236 |
NaN |
NaN |
| M1237 |
NaN |
NaN |
| M1238 |
NaN |
NaN |
| M1239 |
NaN |
NaN |
| M1240 |
NaN |
NaN |
| M1241 |
NaN |
NaN |
| M1242 |
NaN |
NaN |
| M1243 |
NaN |
NaN |
| M1244 |
NaN |
NaN |
| M1245 |
NaN |
NaN |
| M1246 |
NaN |
NaN |
| M1247 |
NaN |
NaN |
| M1248 |
NaN |
NaN |
| M1249 |
NaN |
NaN |
| M1250 |
NaN |
NaN |
| M1251 |
NaN |
NaN |
| M1252 |
NaN |
NaN |
| M1253 |
NaN |
NaN |
| M1254 |
3. Air blower C OFF |
OPTION |
| M1255 |
3. Air blower C ON |
OPTION |